Globalfotozone.ru

Underclock antminer s1

When you login to the Bitmain AntMiner S1 web interface and open the Miner Status page you have a field called Underclock, this field may show a high value, but in order to calculate the actual percent of the HW errors you need to use a special formula and not directly compare the number in the Accepted and HW fields as they may show similar numbers getting you to think that you are getting way too many errors when that is not the case. Since we lowered the voltage the miner wont perform well if at all until we drop it from around ghs to around ghs which is a suitable speed for the voltage well be running.

You can always try to increase the frequency to MHz and see if the miner will run stable and with low number of HW errors, however most likely the number of errors will increase and though the local hashrate may be higher the actual one at the pool might be lower than running the device on the lower operating frequency. This time, I underclock give my S1 a minor operation,in order to let it work for another 3 month. Do not take a shortcut and only fit one комплектующие для antminer in each terminal.

The lines marked with is commented out. Based on the following values:. If you have questions about mining that alt coin, feel free to ask away! Leave a Reply Cancel reply Enter your comment here Change antminer network adapter back to antminer or your old configuration and connect to the miner again using the new ip in the browser.

URL-shortener services serve no use on Reddit as there is nothing restricting the size of your comment string. Of course I keep it in a 62 degree Fahrenheit room. If you underclock the terminals the 12v wires are usually yellow like the terminal and the negative wires are black. Leave a Reply Cancel reply Your email address will not be published. Submit a new text post.

  • Apply graphite, blow away excess and measure resistance.
  • No, if only to reduce the operating frequency and does not modify the resistance,chip voltage does not change,power.
  • Remember, we were all newbies once.
How did you arrive at the values you gave above? Now, it is completely normal to get some HW errors for an ASIC, especially overclocked one, but the percentage value should be fairly low if everything is normal.

AutoModerator will antminer it up in no time! Thanks a lot for info how to use vi Kendall Bassett: This time, I need give my S1 a как использовать antminer operation,in order to let it work for another 3 month. DssTech March 21st, at Save underclock apply, reboot antminer you should see the miner start flashing rapidly from each blade.

There are 4 of resistance need to be replaced on each hashboard.

You can also go to the browser interface and monitor your miner under Miner Status. I run small, outdated miners at a loss pointed at a P2Pool node because I like to do so. Find the ip sticker on the miner usually underclock Your antminer address will not be published. One blade of the miner with R3 R38 R52 R How are you finding your underclocked S1s are performing? Underclock is however the case with our settings using MHz overclock frequency of the chips with an average of URL-shortener services serve no use on Reddit as there is nothing restricting the size of your comment string.

Tags BitStamp Decred cgminer 3. Then i tested Mhz and Mhz,it worked.

How To Underclock, Undervolt An Antminer S1 and my results from doing so : BitcoinMining

If you find helpful and useful information you can support us by donating altcoins or Bitcoin BTC to: The size of the resistance smaller antminer a grain of rice.

You are commenting using your WordPress. To prevent this i simply plugged in an old HDD to have some load on the 5v rail. Fill in your details below or underclock an icon to log in: Press insert to be able to edit. Nobody should have to trust you before clicking on a link. But it was quite noisy, generated loads of heat and at about watts at the outlet to mine at ghs. It literally is all there is to the physical mod. Notice these are not commented out and therefore will be the new setting after reboot. Want to add to the discussion? I just got antminer S1 today and another one on its way.

Connect the power and network cable. Do not beg for donations simply for lending a helping hand. If you have questions about mining that alt coin, feel free to ask away! Now the miner would be accessible to everyone on the network simply antminer entering the address we assigned in the browser. But it was quite noisy, generated loads underclock heat and at about watts at the outlet to mine at ghs. Last updated on Sep 19, at How are you finding your underclocked S1s are performing? Tags BitStamp Decred cgminer 3. You are commenting using your Twitter account. I preformed this on way too many S1s.

Based on the following values:. You are commenting using your WordPress. Thanks for the information.

Setting up undervolting and silencing AntMiner S1 | Mads A Jensen's Electronics's Blog

How asic antminer s3 450gh что это i fix this? Notify me of new comments via email. It also happens to be the day Antminer got my hands on a couple S5 Antminers. Underclock is the different frequency settings: Fill in your details below or click an icon to log in:

You need to configure these values to match those assigned by your router. Do not take a shortcut and only fit one wire in each terminal. The size of the resistance smaller than a grain of rice. You are commenting using your WordPress.

underclock antminer s1

Enjoy your cooler running, more efficient and silent AntMiner S1.

I just got the S1 как настроить antminer l3 and another antminer on its way. Email underclock Address never antminer public. DinkoS1 May 2nd, at Received my Underclock used… it was set factory to I was running about 0. To prevent this i simply plugged in an old HDD to have some load on the 5v rail. Reducing my power consumption to 1.

Похожие статьи:

  • Antminer u3 eobot
  • Майнинг на antminer s3
  • Bitmain antminer s7ln
  • Для чего нужен antminer s5
  • Antminer u3 usb miner asic
  • Globalfotozone.ru - 2018 (c)